Can The Lcd Service Minder & Hour Meter On Cub Cadet Be Reset

11

Functioning

8

Cup Holder

The loving cup holder is located on the meridian of the console.

9

Storage Tray

The storage tray is located to the rear of the panel.

10

Fuel Tank Cap

Turn the fill cap at least ii clicks counter clockwise and pull upward to remove. The

fuel cap is tethered to the tractor to forestall its loss. Do non attempt to remove the

cap from the tractor. Fill tank to ½

" (12.7 mm)below the bottom of the filler neck,

assuasive some space in the tank for fuel expansion. Do non overfill the tank.

Push the cap downward on the fuel tank fill neck and plough at least 2 clicks clockwise to

tighten. E'er re-install the fuel cap tightly onto the fuel tank later on removing.

WARNING

Never fill the fuel tank when the engine is running. If the engine is hot

from recently running, allow to absurd for at least five minutes before

refueling. Highly flammable gasoline could splash onto the engine and

cause a fire.

11

Hour Meter & LCD Service Minder (If equipped)

The LCD service minder volition remind the

operator of

maintenance intervals for

changing the engine oil, air filter service,

low engine and depression battery warnings.

When the key is rotated out of the STOP

position just is not in the Get-go position,

the LCD service minder & hour meter

volition briefly display the bombardment voltage,

followed by the tractor's accumulated

hours.

Note:

When the ignition key is out of the Terminate position the hourglass

symbol

is illuminated/blinks to indicate it is recording the hours of tractor operation,

regardless of whether the engine has been started.

Modify Oil

The LCD screen will alternate the letters "CHG", followed by "OIL", followed by

"Shortly", followed by the meter'due south accumulated time. "CHG/OIL/Shortly/TIME" will

alternate on the display for 7 minutes after the meter reaches fifty hours. This oil

service minder interval volition occur every fifty hours. Earlier the interval expires,

change the engine oil every bit instructed in the Engine Operator's Manual

Low Oil

Note:

The low oil pressure role but works if the engine is equipped with an oil

pressure switch.

The LCD screen volition alternate the letters "LO" followed by "OIL", followed past the

meter'south accumulated time, which indicates the engine has low oil pressure. This is

mutual when starting an engine. The indicator will remain active until the engine

sufficiently builds pressure later on starting. If it remains on with the engine at full

speed and after a few minutes of performance, stop the tractor immediately and bank check

the engine oil level and add together as instructed in the Engine Operator's Manual. If the oil

level is right and the indicator persists, contact an authorized service dealer.

Low Battery

At startup, the bombardment voltage will briefly brandish, and then changes to accumulated

hours. The letters "LO" followed by the letters "BATT" will display, followed by

the meter's accumulated time. "LO/BATT/Fourth dimension" is displayed on the LCD when the

voltage drops below xi.5 volts. When this occurs, the battery is in need of a charge

or the engine'southward charging system is non generating sufficient amperage. Charge

the battery as instructed in the Product Care department of this manual or have the

charging system checked by your local service dealer.

Air Filter Service

The LCD screen volition display the letters "CLN" followed by the letters "AIR", followed

by "FILT", followed by the meter'southward accumulated time. "CLN/AIR/FILT/Fourth dimension" will

alternate on the display for 7 minutes after the meter reaches 25 hours. This air

filter service minder time interval will be every 25 hours. On intervals that are

common with oil service, the oil message will be displayed start followed past the air

filter message.

12

Throttle/Choke Command Lever or Throttle Control Lever

Annotation:

When prepare in a given position, a uniform engine speed volition be maintained.

Throttle Control Lever

(If equipped)

Button the throttle control lever forward to

increase the engine speed. The tractor is

designed to operate with the throttle control

lever at full throttle (FAST) when the tractor is being driven and the tractor deck is

engaged. Pull the throttle control lever rearward to decrease the engine speed.

Throttle/Choke Command

Lever (If equipped)

Push button the throttle/choke control lever

forward to increase the engine speed. The

tractor is designed to operate with the

throttle/choke control lever at full throttle (FAST) when the tractor is being driven and

the mower deck is engaged. Pull the throttle/choke control lever rearward to decrease the

engine speed. When starting the engine, push the control lever fully forward into the "CHOKE"

position. After starting and warming the engine, move the command handle rearward until

you experience it motion past the choke detent. Throttle is not meant to control unit speed, throttle

should remain in high speed while operating blades.

13

Choke Control (If equipped)

The choke control determines the position of the engine choke.

Pull the knob out to choke the engine; button the knob in to open

the choke.

Multi-Tool (If equipped)

The multi-tool (a) is located on

the front of the correct panel.

The multi-tool (a) can exist used

equally a deck elevator lockout, to remove

the footpan bolt, adapt the

height of the lapbar bulldoze control

levers, bulldoze control lever finish

adjustment and can be used

every bit a removal tool with the ½

"

socket end. See the Product Intendance

department for more information

on multi-tool (a) usage. Run across

Figure sixteen.

Headlights (Non shown/If equipped)

The headlights are located on the forepart of the frame. The headlights are ON

whenever the ignition key is rotated out of the Terminate position and OFF when the

ignition key is moved to the Cease position.

Seat Adjustment Lever (Not shown/If equipped)

The seat adjustment lever is located under the seat. The seat aligning lever

allows for adjustment frontwards or backward of the operator's seat. Refer to the

Assembly & Set-Upward section for instructions on adjusting the seat position.

Note:

If your tractor is not equipped with a seat aligning lever, it tin can be adapted

using the knobs on the underside of the seat. Refer to the Assembly & Set-Up

section for instruction on adjusting the seat.

SLOW

FAST

Choke

(a)

Figure sixteen

Can The Lcd Service Minder & Hour Meter On Cub Cadet Be Reset,

Source: https://www.manualowl.com/m/Cub%20Cadet/ZT2-50/Manual/524439?page=11

Posted by: stewartarow1957.blogspot.com

Share this post